欢迎进入东莞市南涯电子有限公司网站
全国服务热线
0769-82011159
DONGGUAN NAN YA ELECTRONICS CO.LTD东 莞 市 南 涯 电 有 限 公 司 |
文件编号 | SF-SP-0372 | |||||||||
| 发布日期 | 2006年5月29日 | ||||||||||
| SPECIFICATION 规格书 | 第A版 | 第1页 共3页 | |||||||||
|
MODEL NO. 产品名称. 拨动开关 |
|||||||||||
| DRAWN 制订 | 白春莲 | APPD. 审批 | |||||||||
| 1.RATING (额 定 值) :DC 50V 0.3A | |||||||||||
| 2.FUNCTION (接触型式) :1P2T | |||||||||||
| 3.TIMING (时间特性) :NOT-SPECIFIED | |||||||||||
| 4.ELECTRICAL CHARACTERISTICS (电气性能规格): | |||||||||||
| ITEM项目 | TEST CONDITIONS 测试条件 | PERFORMANCE 规格 | |||||||||
| 4.1 |
CONTACT RESISTANCE 接触电阻 |
MEASURED AT 1KHZ SMALL CURRENT(100mA OR LESS) 在1KHZ微小电流(100 mA 以下)测试. |
30mΩ MAX. 30毫欧以下。 |
||||||||
| 4.2 |
INSULATION RESISTANCE 绝缘电阻 |
APPLY A VOLTAGE OF 500V DC FOR 1 MIN. TO FOLLOWING PORTIONS AFTER WHICH MEASUREMENT SHALL BE MADE. (1) BETWEEN BODY AND TERMINAL. (2) BETWEEN TERMINALS. 输入500V DC 电压1分钟,按以下接触方法测试; (1) 外壳兴排脚之间. (2) 端子之间. |
100 MΩ MIN 100兆欧以上。 |
||||||||
| 4.3 |
DIELECTRIC STRENGTH 耐电压 |
AC 500V (50-60HZ)FOR 1 MIN TRIP CURRENT:0.5 mA (1) BETWEEN TERMINALS. (2) BETWEEN TNDIVIDUAL TERMINAL AND FRAME. 输入AC 500V(50-60 HZ)电压,1分钟感度电流为0.5 mA,按以下接触方法测试: (1) 排脚相互之间 (2) 排脚兴外壳之间 |
WITHOUT DAMAGE TOPARTS ARCINCINC OR BREAKDCMN, ETC. 没有绝缘破坏等异常. |
||||||||
| 5.MECHANICAL CHARACTERISTICS (机械性能规格) | |||||||||||
| ITEM 项目 | TEST CONDITIONS 测试条件 | PERFORMANCE 规格 | |||||||||
| 5.1 |
OPERATING FORCE 作动力 |
MEASUREMENT SHALL BE MADE AT TRE NEAREST POINT OF THE COMPONENT OR AT THE POINT 3mm FROM THE TIP OF THE ACTUATOR (KNOB). 在距离胶柄前端3 mm作测定点. |
300gf±100gf | ||||||||
| 5.2 |
TERMINAL BTRENGTH 端子强度 |
A STATIC LOAD OF 300 gf SHALL BE APPLIED TO THE TERMINAL FOR 15 SEC.IN ANY DIRECTION 在排脚前端任意一个方向加300 gf力度测试, |
MECHANICAL AND ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED WITHOUT DAMAGE OR EXCESSIVE LOOSENESS OF ACTUATOR. 在端子中没有裂开、松动等异常,满足于机械、电器性能 |
||||||||
| 5.3 |
DISPLACEMENT OF ACTUATOR (KNOB) 柄强度 |
A STATIC LOAD OF 10 N(1K gf)SHALL BE APPLIED TO THE TOP OF THE ACTUATOR(KNOB) AND THEN DISPLACEMENT SHALL BE MEASURED TO THE DIR-ECTION OF THE ARROW. 在柄的前端施加1K gf的力度,位移应沿印记的方向上定. |
THE LEVER SHALL HAVE NO SERIOUS DEFORMATION AND FUNCTION IS NORMALLY. 柄部无严重变形,可以正常工作. |
||||||||
|
DONGGUAN NAN YA ELECTRONICS CO.LTD 东 莞 市 南 涯 电 子 有 限 公 司 |
文件编号 | SF-SP-0372 | |||
| 发布日期 | 2006年5月29日 | ||||
| SPECIFICATION 规格书 | 第A版 | 第2页 共3页 | |||
| 6.ENDURANCE CHARACTERISTICS(耐久性): | |||||
| ITEM 项目 | TIST CONDITIONS 测试条件 | PERFORMANCE 规格 | |||
| 6.1 |
LIFE TEST 寿命试验 |
ENDURANCE WITHOUT LOADING： A SWITCH SHALL BE SUBJECTED TO 10，000 CYCLES AT A SPEED OF 15 TO 18 CYCLES PER MINUTE WITHOUT LOADING. 无负荷: 在无负荷的条件下以每分钟15-18回的 速度进行10,000次的测试. |
（1）CONTACT RESISTANCE（接触电阻） 100mΩ MAX,100毫欧以下。 （2）INSULATION RESISTANCE（绝缘电阻） 50MΩ MIN，50兆欧以上。 （3）WITHSTAND VOLTAGE（耐电压） AC 500V，1 MINUTE.AC 500V 1分钟 （4）OPERATING FORCE(作动力) ±30% INITIAL VALUE. 变化范围初始值±30%. （5）WITHOUT DAMAGE TO PARTS ARCING OR BREAKDOWN ETC. (测试后外表无损伤,并且满足机械性能) |
||
| 6.2 |
SOLDERA- BILITY TEST 可焊性试验 |
THE TOP OF THE TERMINALS SHALL BE DIPPED 2mm IN THE SOLDER BATH OF 230±5℃ FOR 3±0.5 SECONDS. 端子顶部被浸入锡焊池中2 mm深,温度 为230±5℃, 时间为3±0.5秒。 |
THE AREA OF SOLDERING. SHOULD BE OVER 75%. 焊接面积要有75%以上. |
||
| 6.3 |
RESISTANCE TO SOLDERING HEAT TEST 耐焊性试验 |
SOLDER BATH METHOD: SOLDER TEMPERATURE 260±5℃ IMMERSION TIME 3±0.5SEC IMMERSION DEPTH UP TO THE SURFACE OF THE BOARD THICKNESS OF PRINTED WIRING BOARD 1.6 mm DIMENSIONS OFCOMPONENT HOLES IN THE PRINTED WIRING BOARD SHALL SEING ACCORDANCE WITH THOSE SPECIFIED IN THIS SPECIFICATION. 焊炉焊接的时候 时候控制在260±5℃，过炉时间3±0.5秒，于（基板）厚度为1.6 mm |
WITHOUT DEFORMATION OF CASE OR EXCESSIVE LOOSENESS OF TEMINALS ELECTRICAL CHARACTERISTICS SHALL BE SATISFIED. 本体无变形,能满足于机械、电器性能。 |
||
| 6.4 |
COLD TEST 耐冷试验 |
THE SWITCH SHALL BE STORED AT A TEMPERATURE OF -25±3℃ FOR 48 HOURS. THEN THE SWITOH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE.-25±3℃中48小时后,再放置常温 常温中1小时来进行测试。 |
THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电器性能。 |
||
|
DONGGUAN NAN YA ELECTRONICS CO.LTD 东 莞 市 南 涯 电 子 有 限 公 司 |
文件编号 | SF-SP-0372 | ||
| 发布日期 | 2006年5月29日 | |||
| SPECIFICATION 规格书 | 第A版 | 第3页 共3页 | ||
| 6.5 |
HEAT TEST 耐热试验 |
THE SWITCH SHALL BE STORED AT A TEMPERATURE O 70±2℃ FOR 48 HOURS. THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITIONS FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置在温度70±2℃中测试48小时后,再放置正常室温中1小时来测定. |
THERE SHALL BE NO DEFORMATION OR CRACKS IN MOLDED PART. 外观无异常,满足于机械、电器性能。 |
|
| 6.6 |
HUMIDITY TEST 潮湿试验 |
THE SWITCH SHALL BE STORED AT A TEMPERATUREOF 40±2℃ AND A HUMIDITY OF 90% TO 95% FOR 96 HOURS.THEN THE SWITCH SHALL BE MAINTAINED AT STANDARD ATMOSPHERIC CONDITION FOR 1 HOUR AFTER WHICH MEASUREMENT SHALL BE MADE. 放置40±2℃的相对温度为90%~95%环境中96小时后,再将样版放在正常环境1小时后进行测试. |
||
| 6.7 |
STANDARD ATMOSPHERIC CONDITIONS 测试标准状态 |
UNLELL OTHERWISE SPECIFIED. THE STANDARD RANGE OF ATMOSPHERIC CONDITIONS FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: （1）AMBIENT TEMPERATURE : 5℃ TO 35℃ （2）RELATIVE HUMIDITY :45% TO 85% （3）AIR PRESSURE :86kpa TO 106kpa 在没有指定的情况下测试温度、湿度、气压如下: （1）温度为5~35℃. （2）湿度为45% TO 85%. （3）气压为86kpa TO 106kpa. |
||
| 6.8 |
PRACTICAL TEMPERATURE RANGE 使用温度范围 |
-16℃~+60℃. 在-16℃~+60℃内使用. |
||
在线客服
